Joomla 1.5 Template By Youjoomla.com

 

GLAD800 System (Global Lake Drilling to 800 meters depth)

The GLAD800 drilling platform on Lake Titicaca, Peru

• Depth Capacity Coring (Wireline or Conventional)
  HMQ Wireline 1200m
  DLS Wireline 800m

• Weight
  Rig Weight: 19,000 lb (8,617 kg)

• Chuck Assembly
  Type Hydraulic Open, Spring Closed
  Maximum Inside Diameter: 4-5/8 in (117 mm)
  Holding Capacity: 40,000 lb (18,181 kg)

• Feed System
  Stroke: 11.5 ft (3.5 m)
  Thrust: 15,000 lb (6,800 kg)
  Pull: 30,000 lb (13,600 kg)

• Hoisting Capacity
  Main
  Capacity: Single Line-Bare Drum 17,500 lb (7,955 kg)
  Capacity: Double Line-Bare Drum 35,000 lb (15,900 kg)
  Cable Size: 110 ft (33.6 m) x 3/4 in (19.0 mm)
  Wireline
  Capacity: Single Line-Bare Drum 2,500 lb (1,136 kg)
  Capacity: Single Line-Bare Drum 840 lb (382 kg)
  Line Speed: Full Drum 1,260 ft/min (984 m/min)
  Cable Size: 4,000 ft (975 m) x 1/4 in

• Standard Equipment
  Dump Mast
  Derrick in Two Sections
  Foot Clamp 5 1/2 in (139.7 mm)
  Thrust: 15,000 lb (6,800 kg)

• Mud Pump Hydraulic Drive - Standard Equipment
  Type: FMC L11 22D
  Max Flow: 72 gpm (272 lpm)
  Max Pressure: 1,000 psi (7 Mpa)

• Power Unit
  Mfg: Cummins 175 hp
  Engine Type: 6 Cyl. Diesel Turbocharged

• Funding
  The GLAD800 is a joint venture between DOSECC and ICDP (International Continental Scientific Drilling Program). The system is operated by DOSECC.

---

GLAD200 System (Global Lake Drilling to 200 meters depth) 

 

 

---

Dynamic Positioning System

The DP system on Lake Malawi, Africa

In water depths greater than about 200 m, anchoring becomes less effective as a means of maintaining the position of a drilling vessel. In these deeper waters, Dynamic Positioning (DP) is required. DOSECC has acquired a portable DP system with funding from the National Science Foundation and the International Continental Scientific Drilling Program. This unit is intended to be able to convert vessels of opportunity into drilling platforms. The system consists of four thrusters powered by four dieselhydraulic power packs. The system is controlled by a Nautronix JSDP5000 (DP-1 class) system that uses either a GPS signal or a seabed beacon for position keeping. The specifications of this system are provided in the following table.

• Thrusters
  Four hydraulic thrusters yielding 8,000 lbf each
  Propeller: 39-inch, 4-blade Kaplan, manganese-bronze with Kort 19-A nozzle
  Mounting: Thruster on mini-skid, positioned and attached according to vessel structural
  members.
  Weight: 5,800 lbs. each
• Hydraulic Power Units
  Four Cat 3406 diesels delivering up to 360 BHP @ 1800 rpm (full load)
  Fuel Consumption: 17.5 US gallons per hour at full load
  Day Tank Capacity: 150 US gallons
  Dimensions: 11'-43/4" long X 5'-7" wide X 9'-31/8" high. Note: an additional 3' is minimum clearance required at both ends of HPU for air inflow and outflow, making effective length requirement of 17'-43/4".
  Weight: 11,300 lbs. Each
  Placement: Within 50' of thruster
  Four roofs for power units
  Four muffler / exhaust systems
  Connecting hose bundle: 6 hoses, overall diameter of 6" (Old, probably need replacement)
• Controller
  Nautronix JSDP5000 Dynamic Positioning System (DP-1 class)
  Consisting of: 2 underwater beacons and battery packs
  1 hydrophone and cable
  1 control console / computer

---

Active Heave Compensated Drilling System

DOSECC's AHC-800 is an active heave compensated (AHC) coring rig that is capable of retrieving continuous core to depths of 800 m (water + sediment) in shallow marine and deep lacustrine environments. The system is modular and designed to fit on a variety of drilling platforms. The AHC-800 is designed to compensate for up to 8 feet of heave with a period of 8 seconds.

The AHC-800 uses a set of proven sampling tools that include:

• Shelby "push" tube
• Hydraulic Piston core (HPC)
• Extended Shoe, non-rotating
• Extended Core Bit, rotating ("The Alien")
• Diamond Core Bit (mining)
• Non-Sampling Assembly

The tools core a hole 5.50 inches (139.7 mm) in diameter. Most are designed to collect core within a plastic liner with an inner diameter.

 

 

 

 

 

 

 

 

 

 

---

DOSECC MONTCO Offshore Drilling Platform

 

 

 

The DOSECC MONTCO drilling platform includes a drilling rig mounted on a liftboat. This configuration allows drilling to continue during almost any sea condition.

 

 

---

 

CS-14 CORING RIG

• Depth capacity
  1200 meters (4040 Feet) with NQ string
  800 Meters (2690 Feet) with HQ string
  475 Meters (1550 Feet) with PQ string
• Chuck Assembly
  Type: Self-centering five-jaw
  Maximum Inside Diameter: 117mm (4 ? in)
• Hoisting Capacity
  Main: 80 kN (18,000lb)
• Standard Equipment
  1.22 m (4 ft) Leveling Hydraulic Supports
  Foot Clamp:139.7mm (5.5 in)
  Trido 140 water pump
• Power Unit
  Stage II Cummins diesel engine
• Feed System
  Stroke: 3.5 m (11.5 Feet)

 

 

 

 

 

 

 

 

 

 

---

 

CS-4002 CORING RIG

• Depth Capacity Coring
  NQ Wireline: 2,450 m (8,030 ft)
  HQ Wireline: 1,600 m (5,250 ft)
  PQ Wireline: 1,050 m (3,440 ft)
  Mast and Feed System
• Feed Travel: 3.35 m (11 ft)
  Feed Speeds: Fast and slow with variable control
  Pull Back: 200 kN (45,000 lbf)
  Thrust: 89 kN (20,000 lbf)
  Rod Pull Length: 6.1 m (20 ft) or 9.1 m (30 ft)
  Drilling Angle: 45 To 90 Degrees
  Mast Dump: 2 m (80 in)
• Power Unit
  Mfg.: Cummins Qsc Pu 8.3 Liter 6 Cylinder
  Power: 212 Kw (285 Hp) @ 2,100 rpm
  Type: Diesel Turbo Charged/Charge Air Cooled
  Cooling: Water
• Hydraulic Pumps
  Primary Pump: Rotation, Hoist, W/L Hoist, Fast Feed
  Auxiliary Pump: Slow Feed, Chuck, Foot Clamp, Mud Mixer
  Chuck Assembly
• Maximum Inside Diameter: 117 mm (4 5/8 in)
  Holding Capacity: 178 kN (40,000 lbf)
  Operation: Spring Applied, Hydraulically Opened
• Drillhead
  Maximum Rpm: 1,300
  Maximum Torque: 6,230 nM (4,596 ft lbf)
  Transmission: Four Speed, Manual Shift
  Mounting: Hydraulic Powered Slide Away
  Lubrication: Pressure System
• Main Host
  Single Line Capacity: 178 kN (40,000 lbf)
  Line Speed: 36 – 71 m/min (117 - 232 fpm)
  Cable Diameter: 22 mm (7/8 in)
• Wire Line Hoist Capacity
  2,600 m (8,530 ft) of 6.35 m (1/4 in) cable
  4,600 m (15,090 ft) of 4.76 mm (3/16 in) cable
  Line Speed: Bare 1.38 m/s (272 fpm) full 5.1 m/s (1004 fpm)
  Line Pull: Bare 28.5 kN (6,380 lbf) full 5.1 kN (1,151 lbf)
• Standard Equipment
  Four Hydraulic Jacks 610 mm (24 in) stroke
  Hydraulic P-Size Holding Clamp
  Control Panel Hydraulic Slide
  High Altitude Kit
  Hydraulic Mud Mixer
  Fuel Tank 950 l (250 gal)
  Mud Pump: Hydraulic Driven FMC W1122bcd
  Max Flow: 140 lpm (37 gpm)
  Max Pressure: 7.0 mpa (1,000 psi)
• Weight
  Rig Weight: 13,380 Kg (29,500 lbs)
  Truck GVW: 36,287 Kg (80,000 lbs)
  Total Weight: 49,667 Kg (109,500 lbs)

 

---

 

CS-1500 CORING RIG

• Depth Capacity
  PQ Wireline: 800 Meters (2690 Feet)
  HQ Wireline: 1200 Meters (3940 Feet)
• Chuck Assembly
  Type: Hydraulic Open, Spring Closed
  Maximum Inside Diameter: 117mm (4-5/8 in)
  Holding Capacity: 18,181 kg (40,000 lb)
• Hoisting Capacity
  Main:
  Single Line Bare Drum: 7955 kg (17,500 lb)
  Double Line Bare Drum: 15,900 kg (35,000 lb)
  Cable Size: 33.6 mm (110 ft) by 19 mm (3/4 in) diameter
  Wireline:
  Single Line Bare Drum: 1136 kg (2,500 lb)
  Single Line Full Drum: 382 kg(840 lb)
  Line Speed Full Drum: 984 m/min (1260 ft/min)
  Cable Length: 975 m (4000 ft) by 6.3 mm (1/4 in)
• Standard Equipment
  Steel Dump Mast with One Steel Derrick Sections
  0.6 m (2 ft) Leveling Hydraulic Supports
  Foot Clamp: 139.7 mm (5.5 in)
• Power Unit
  Cummins 175 Hp diesel engine
  Engine Type: 6-cylinder turbo-charge diesel
• Feed System
  Stroke: 3.5 m (11.5 Feet)
  Thrust: 6800 kg (15,000 lb)
  Pull: 13,600 kg (30,000 lb)
• Mud Pump
  FMC W1122 (hydraulic)
  Max. Flow: 272 lpm (72 gpm) DOSECC Exploration Services, LLC
  Max. Pressure: 7 Mpa (1000 psi)

 

---

T3WDH DRILLING RIG  

CS500 DRILLING RIG

• Drilling Rig Weight
• 2267 kg (5000 lb), modular, man- or helicopter-portable
• Depth Capacity
  PQ Wireline: 200 Meters (670 Feet)
  HQ Wireline: 300 Meters (985 Feet)
• Chuck Assembly
  Type: Hydraulic Open, Spring Closed
  Maximum Inside Diameter: 117mm (4-5/8 in)
• Holding Capacity: 18,181 kg (40,000 lb)
• Hoisting Capacity
  Main:
  Single Line Bare Drum: 2727 kg (6000 lb)
  Max. Line Speed: 38 m/min (126 ft/min)
  Double Line Bare Drum: 15,900 kg (35,000 lb)
  Cable Size: 33 mm (1/2 in) diameter
  Wireline:
  Single Line Bare Drum: 1550 kg (3400 lb)
  Single Line Full Drum: 540 kg(1200 lb)
  Max. Line Speed Bare Drum: 80 m/min (260 ft/min)
  Max. Line Speed: 244 m/min (800 ft/min)
  Cable Size: 5 mm (3/16 in)
• Standard Equipment
  Steel Dump Derrick with Two Aluminum Mast Sections
  1.22 m (4 ft) Leveling Hydraulic Supports
  Foot Clamp: 139.7 mm (5.5 in)
• Power Unit
  2 Lombardini 1204/T
  Engine Type: 4-cylinder turbo-charge diesel
  31.2 kW (42 Hp) @ 3600 rpm each
• Feed System
  Stroke: 1.8 m (6 Feet)
  Thrust: 3200 kg (7000 lb)
  Pull: 4500 kg (10,000 lb)
• Mud Pump
  FMC Triplex Bean Pump
  Driven by One Isuzu LB1 Diesel Engine
  20.6 kW (27.6 Hp) @ 3450 rpm
  Max. Flow: 200 lpm (53 gpm)
  Max. Pressure: 7 Mpa (1000 psi)